홈 제품 소개 연료 시스템 일부

실리콘 진동판 모델 Ｊ IMPCO 수리용 장비

모든 제품

연료 시스템 일부 (60)

IMPCO 중간 사이즈 엔진 믹서 (18)

IMPCO 대형 엔진 믹서 (14)

IMPCO 규제 기관 (6)

저압 레귤레이터 (7)

고압 규제 기관 (3)

IMPCO 수리용 장비 (6)

IMPCO 가스믹서 (13)

IMPCO 잠김 분리 (12)

IMPCO LPG 부분 (47)

중국 guangqing(anhui)gas technologies co.,ltd. 인증

제가 지금 온라인 채팅 해요

실리콘 진동판 모델 Ｊ IMPCO 수리용 장비

Name: 실리콘 진동판 모델 Ｊ IMPCO 수리용 장비
Brand: IMPCO
SKU: RK-COBRA
Price: 1.00 USD
Availability: InStock
Rating: 4.5 (134 reviews)

Silicone Diaphragm Model J IMPCO Repair Kits

큰 이미지 : 실리콘 진동판 모델 Ｊ IMPCO 수리용 장비

제품 상세 정보:

원래 장소:	미국
브랜드 이름:	IMPCO
모델 번호:	RK-COBRA

결제 및 배송 조건:

최소 주문 수량:	24
가격:	Depending on quantity
포장 세부 사항:	통
배달 시간:	8 주
지불 조건:	전신환
공급 능력:	8weeks 당 1200pcs

접촉

상세 제품 설명

상품 이름:

수리용 연장통

부품번호:

RK-J-2

브랜드:

IMPCO

격막:

실리콘 (황색)

하이 라이트:

실리콘 진동판 IMPCO 수리용 장비

Ｊ IMPCO 수리용 장비를 모델링하세요

IMPCO RK-J-2 , Model J Converter Repair Kit , Yellow Coded Diapragm

The IMPCO RK-J-2 repair kit will provide

the technician information to successfully repair the

Model J converter. Always inspect the major casting pieces for damage, corrosion or cracks before attempting a service repair. Be sure the repair kit part number you are using is correct for the regulator being serviced. Diaphragms is yellow - silicone diaphragm material is the optional upgrade material that provides excellent flexibility in cold weather climates and is more resistant to chemical contamination.

REBUILD INSTRUCTIONS

1. Under normal conditions, installation of a complete Model J Repair Kit should be necessary only at the time of a major engine overhaul or when the converter has been out of service for an extended period of time. Each kit includes the necessary gaskets, diaphragms, seals and some replacement screws.

2. Remove the 6 screws (2) from the secondary cover assembly (3).

NOTE: Identify type and location of screws removed (i.e. Torx) to ensure the same type and size screws are returned to the correct locations during reassembly.

3. Loosen the secondary cover (3) by tapping around the circumference with a plastic screw driver handle.

4. Remove the secondary cover (3) and secondary dia-phragm (4) as a unit. Note the secondary lever (6) pro-truding through the metal tab slot of the secondary dia-phragm. Slide the cover and diaphragm toward the gas inlet to free the lever from the slotted tab of the dia-phragm. Take care not to bend the lever.

5. Remove the screw (5) retaining the secondary lever fulcrum pin.

6. Remove the secondary lever (6) and fulcrum pin (7). Set aside fulcrum pin for reassembly. Remove the secondary spring (9).

7. Turn the converter over. Remove the seven screws (20) and lift off the primary cover (19).

8. Remove the primary diaphragm (18).

9. Remove the primary valve pin (17) and spring (16).

10. Remove plate (14) and the gasket (13).

11. Remove the gasket (13) from the plate (14). Clean plate as needed to ensure a good seal with a new gas-ket.

12. Remove the primary seat (12). Clean covers (3, 14, & 19), body (10) and all other metal parts as necessary with a safety solvent as needed and allow to dry prior to reassembly. Do not use harsh solvents such as brake or carburetor cleaner on any of the non-metallic components as they will damage the material.

13. Install new primary seat (12).

14. Set new plate gasket (13) on the plate (14). The pri-mary pressure hole in the gasket must line up with the hole in the body cover plate as noted in the photo at left.

15. Place the plate (14) and gasket (13) on to the body (10) and align the screw holes.

16. Insert the new primary valve pin (17) through the spring (16) and insert into the plate (14) with the larger diame-ter end of the spring resting against the plate.

17. Set the primary diaphragm (18) in place on the plate (14). Line up the screw holes to the plate.

18. Carefully place the primary cover (19) over the dia-phragm (18). Hand-thread the screws (20) through the cover and plate (14) into the converter body (10).

19. Tighten the screws (20) to 37-43 in-lb. (4.2-4.9 N•m) in a criss-cross pattern.

20. Assemble the new secondary seat (8) and new sec-ondary lever (6) by inserting the seat retaining tip to the end opening of the lever as shown. Be sure the new seat properly locks into place.

21. Position the secondary spring (9) in place on the body (10). Place the secondary lever assembly (6 & 8) into place over the spring (9).

22. Hold the lever assembly (6 & 8) with the fulcrum pin (7) in place in its locating groove and fasten in place with the retaining screw (5).

23. Tighten the screw (5) to 29-35 in.lbs. (3.3-4.0 N•m).

24. The end of the secondary lever (6) should be 1/32" be-low the level of the body casting (10). Use a straight edge to measure. Remove and gently bend the lever if necessary to obtain the correct height.

NOTE: Bending the lever while installed may result in damage to the seat (8). Remove the lever from the body, bend, reinstall, and then re-check the height.

25. Align the secondary diaphragm (4) to the secondary lever (6) as shown. The end of the lever must protrude through the tab slot on the bottom of the new dia-phragm (4) after installation. The gap from which the link is punched should be located toward the gas inlet.

26. Install the secondary cover (3) with the six screws (2).

27. Tighten the screws (2) in a crisscross pattern to 29-35 in-lb. (3.3-4.0 N•m), to complete the installation of the repair kit components.

28. Attach a 100 psi air pressure hose to the regulator "IN-LET" fitting.

29. For models with a primer button: Depress the primer button several times. Air flow should be detected when the primer is depressed.

NOTE: Not all models include a primer button. Skip this step for models without a primer button.

30. Check the primary cover for leaks using liquid leak de-tector solution.

31. Make sure one of the regulator's secondary outlets is plugged. Draw a bubble of leak solution over the other regulator outlet. The bubble should hold for several se-conds when the regulator is pressurized. If any leaks are found, the regulator must be replaced. If no leaks are found, the regulator can be reinstalled and returned to service.

태그:

담당자: Mrs. Carrie Liu

전화 번호: +86 13855195806

팩스: 86-551-63664756

기타 제품

UL 모델 CA125 6 IMPCO 가스믹서 연료 시스템 일부

부분 묘사: 믹서

부품번호: CA125-6

브랜드: IMPCO

가스형태: LPG 수증기 천연 가스

설비를 섞는 IMPCO 개요 / 낮은 열 가스 DG200M 2시 2분 가스

상품 이름: 믹서

연료 유형: 다이제스트 저열 가스

설치 위치: 수직

격막 물자: (표준) Hydrin, (선택) 실리콘

검은 코드화되 다이아프람 임프코 코브라 수리 연료 시스템 일부

상품 이름: 수리용 연장통

부품번호: RK-J

브랜드: IMPCO

격막: Hydrin (검정)

표준 공기 밸브 RK CA55 2 IMPCO 연료 시스템 일부

상품 이름: 수리용 연장통

부품번호: RK-CA55-2

브랜드: IMPCO

공기 연료 비율: 경사

플루오로 실리콘 진동판 RK VFF30 3 IMPCO 수리용 장비

상품 이름: 수리용 연장통

부품번호: RK-VFF30-3

브랜드: IMPCO

격막: 플루오로 실리콘

실리콘 진동판 모델 Ｊ IMPCO 수리용 장비

실리콘 진동판 모델 Ｊ IMPCO 수리용 장비

실리콘 진동판 IMPCO 수리용 장비

Ｊ IMPCO 수리용 장비를 모델링하세요

임프코 연료 시스템 PF 052FM,

450098 001 연료 시스템 일부,

여과 15 마이크론 PF 052FM